StartMade Blog Episode 169 ·

The "N52" Neodymium Magnets Lost Their Strength After One Summer

Neodymium Magnet Grade, Pull Force and Coating Testing Guide for Car Mounts, Phone Cases, Bags, Furniture and Toys

Hello, this is StartMade.

A brand selling car accessories imported 240,000 disc magnets from a magnet factory in Ningbo (宁波), Zhejiang, for its magnetic car phone mounts. The magnets were 20mm in diameter and 2mm thick, four per mount, enough for 60,000 sets. The purchase order said "N52 钕铁硼磁铁, 镀镍 (N52 NdFeB magnet, nickel plated)," and the factory sent a measurement sheet stating "表面高斯3000以上 (surface gauss above 3,000)." With a phone attached, the sample did not budge when shaken, and inspection passed everything: dimensions, appearance, even surface gauss.

The problem surfaced in reviews from July. Comments like "my phone fell off going over a speed bump" and "definitely weaker than at first" piled up, and customers in coastal areas posted photos of rust around the magnet edges. Testing the remaining stock at a lab showed the magnets were not N52 but around N38, and in the standard (N) temperature grade with a maximum working temperature of roughly 80°C. A dashboard in midsummer easily goes past 80°C, so the heat had taken the magnets' strength. The nickel plating was also a thin single layer rather than three layers. The factory contact answered: "高斯够就行,N52和N38用户分不出来 (As long as the gauss is there, it's fine. Users can't tell N52 from N38)."

Magnet grades cannot be told apart by eye or by hand. A new magnet, whether N35 or N52, snaps hard onto steel. The difference only shows after heat, moisture or a few months of use, and by then everything has been sold. With magnetic toys a child could swallow, the problem grows from returns into safety incidents. This post covers what the N number and temperature grades mean, standards that differ by product and market, checking methods and their limits, approximate criteria, gaps in test reports, common supplier substitutions, and what to cover in the spec sheet and at inspection.

Words like "N52", "强磁 (strong magnet)" or "高斯3000 (gauss 3,000)" guarantee nothing on their own. Write the magnet material and grade (N number), temperature grade (N, M, H, SH, etc.), dimensions and tolerances, magnetization direction and polarity, coating type and thickness, and finished-product pull force into the spec sheet, then measure samples pulled from mass production. That is what keeps you from summer complaints and from getting stuck at sales channel reviews and air shipping.

Note This post is based on common practices of magnet, electronic accessory and toy factories in Ningbo and Cixi (慈溪) in Zhejiang, Ganzhou (赣州) in Jiangxi, and Shenzhen, Dongguan and Shantou in Guangdong as of November 2026, widely used industry criteria, and public standards such as China's GB/T 13560 (sintered NdFeB permanent magnets), IEC 60404-8-1, EN 71-1, ASTM F963, US 16 CFR 1262 and IATA Dangerous Goods Regulations PI 953. The figures in this post are approximate values used in practice. Safety and transport rules for magnets differ by product, user age and sales market and change often, so always confirm the requirements that apply with the certification body, test lab and freight forwarder.

1. Every Magnet Feels Strong in Your Hand - Why Grades Are Invisible

The first check both factories and inspectors make is to stick the magnet to a piece of steel, or attach a phone and shake it. If it does not fall, the sheet says "magnetic force OK." But even the lowest grade of neodymium magnet is hard to pull off by hand. The difference between N35 and N52 at the same size is roughly 20 to 30 percent, and a difference that size is almost impossible to feel.

The "表面高斯 (surface gauss)" value that factories commonly send does not reveal the grade either. Surface gauss varies widely with magnet size and thickness, measuring position and the height of the probe sensor. A thick N35 magnet often reads higher surface gauss than a thin N52 magnet. Even on the same magnet, measuring the center versus the edge can swing the reading by hundreds of gauss. A gauss value without stated measuring conditions is no basis for comparison.

Being strong when new is not the end of it either. Neodymium magnets weaken as temperature rises, and once they pass the limit temperature of their grade, part of the strength does not come back after cooling. Iron is the main ingredient, so if the plating is thin or scratched, moisture rusts it quickly, and once rust spreads inside the magnet crumbles. Inspection only looks at new magnets at room temperature, so the goods ship without anyone checking how they perform in a hot car in summer, a bathroom or by the sea. Plating corrosion testing was covered in Episode 128; this post focuses on the magnet's own grade, strength, heat resistance and coating.


2. What N35, N52, H and SH Actually Mean

The number in "N52" is the maximum energy product ((BH)max) in MGOe. The higher the number, the stronger the magnet at the same size. The letters after it indicate resistance to heat (intrinsic coercivity, Hcj). The plain N grade is generally considered usable up to about 80°C, M to 100°C, H to 120°C, SH to 150°C, UH to 180°C and EH to around 200°C. The number and the letters are independent values, so writing only "N52" leaves the temperature condition at the weakest grade.

Magnet TypeChinese Factory TermFeaturesWeaknesses
Sintered neodymium (NdFeB)烧结钕铁硼, 强磁Strongest permanent magnet, high force from small sizeRusts easily so coating is essential, brittle, loses strength at high temperature
High-temperature grade neodymium耐高温钕铁硼, H/SH/UH料Dysprosium or terbium added to raise coercivity, for environments above 100°CHigher price, affected by heavy rare earth prices and export controls
Bonded neodymium粘结钕铁硼Magnet powder set in resin, complex shapes, precise dimensionsMuch weaker than sintered, easily mistaken for sintered
Ferrite铁氧体, 黑磁Cheap and rust-free, for fridge magnets and speakersAbout one third the strength of neodymium, needs larger size
Rubber magnet橡胶磁, 软磁Ferrite powder mixed into rubber, flexible, for sheets and stickersWeakest of all

When a factory says "强磁," it usually means sintered neodymium, but within that there are dozens of combinations of grade, temperature grade and coating. Even among "N52" magnets, depending on alloy and sintering quality, some measure just at the bottom of the grade range and others clear it comfortably.


3. Standards That Differ by Product and Market

Magnets are not certified as products in themselves. The standards that apply depend on where they go. The same 10mm magnet faces completely different questions in a bag closure and in a child's magnetic building block.

ProductMain RiskKoreaUSEU / UK
Magnetic toys and building blocksMagnets come loose and are swallowed, intestinal perforationMagnet clauses of the toy safety standard (children's product KC)ASTM F963 magnet clauses, small magnets with flux index above 50 restrictedEN 71-1 magnet clauses, flux index criteria and warnings
Magnet sets (adult puzzles, desk toys)Swallowed if children get accessCheck by product, warning labels16 CFR 1262, small magnets below flux index 50General Product Safety Regulation (GPSR), warnings
Car mounts and phone casesHeat demagnetization, drops, device interferenceGeneral goods, labeling responsibilityGeneral product liabilityGPSR
Bag and clothing closures, cabinet catchesRust, weakening, pacemaker interference warningsLabeling by productGeneral product liabilityGPSR, warnings
Air shipping of any product containing magnetsInterference with aircraft instrumentsIATA PI 953 magnetized material rulesIATA PI 953IATA PI 953

The biggest risk is small magnets a child can swallow. If two or more are swallowed, they can attract each other through the intestinal walls and perforate the bowel, so many countries tightly restrict "magnets small enough to fit in the small parts cylinder with a flux index above 50 kG²mm²" in children's products. Some buyers raise the grade thinking stronger is always better, only to fail the safety standard. See Episode 65 for children's product import requirements and Episode 10 for product certification in general.


4. Checking Methods - From Sticking It On to BH Curve Measurement

Ask "是N52吗? (Is it N52?)" and the factory almost always answers "是的,N52 (Yes, N52)." The only way to verify that is to measure, and each method shows a clearly different range of things.

MethodHow It WorksWhat It ShowsLimits
Sticking it on by handAttach to a steel plate or phone and shakeOnly whether there is no magnet or a far weaker oneGrade differences almost impossible to tell
Gaussmeter surface fieldHall probe placed at the center of the magnet surfaceRelative comparison between same-size magnets under the same conditionsValue swings widely with size, position and probe height; cannot determine grade
Pull force testMeasure the force to pull the magnet vertically off a steel plate of set thicknessValue closest to real-use performanceChanges with plate thickness, surface and speed; meaningful only against a reference sample
Fluxmeter and Helmholtz coilMeasure magnetic moment with the magnet inside a coilStrength comparison with less size effect, Br estimateNeeds equipment; says nothing about coercivity or heat performance
BH curve measurement (hysteresigraph)Lab equipment measures the full demagnetization curveBr, Hcb, Hcj, (BH)max, actual gradeSpecimen shape limits, cost and time
High-temperature demagnetization testHold at working temperature for a set time, then remeasure at room temperatureStrength loss in a hot car or inside a deviceTemperature, time and magnet shape (permeance) must be fixed to compare
Salt spray and PCTExposure to salt fog or high-temperature, high-pressure steamCoating corrosion resistance, corrosion resistance of the magnet material itselfTakes a long time; conditions must be set in the spec sheet
Coating thickness, density and XRFMeasure coating by cross-section or X-ray, check density and elementsCoating layers and thickness, ferrite or bonded magnets mixed in, dysprosium contentSays nothing about strength itself

Pull Force Only Becomes a Number When You State "On Which Steel Plate"

Catalog pull force figures are usually ideal values measured with the magnet directly on thick mild steel. In a real product, case plastic, leather or adhesive tape sits between the magnet and the mating plate, and the mating plate is thin. So the spec sheet should not quote the catalog value but state the assembled condition, such as "at least ○N on the approved finished sample, on the specified steel plate and conditions." With that one number, you can see right away how many percent weaker mass production is than the sample.

Nobody Knows the Heat Resistance Unless It Is Tested Separately

N-grade magnets are perfectly strong at room temperature. The difference appears after heat. For magnets in car mounts, laptop and tablet accessories, or near motors and lights, require a test that holds them at the maximum temperature of the use environment for a few hours and then remeasures surface field or pull force at room temperature. The thinner and wider the magnet, the more heat weakens it even within the same grade, so always test in the actual shape.

Only a BH Curve Can Confirm the Grade

To establish whether a magnet is N38 or N52, H or plain N, a lab has to measure the BH curve. Simple shapes like discs and blocks can be measured as they are; very small or complex shapes are measured with specimens cut from a block of the same lot. It costs money, but doing it once at sample approval and once at the first production run lets you manage later lots by comparing pull force and surface field against that baseline.


5. Approximate Criteria

Below is a summary of values commonly used in China's GB/T 13560 and industry catalogs. Grade ranges differ slightly between factories, so before sending anything to a lab, decide which table you will judge against.

GradeRemanence BrMax Energy Product (BH)maxCoercivity Hcj (min)Max Working Temp (reference)
N35approx. 1.17-1.22 Tapprox. 33-36 MGOe12 kOe or moreapprox. 80°C
N42approx. 1.28-1.32 Tapprox. 40-42 MGOe12 kOe or moreapprox. 80°C
N52approx. 1.42-1.48 Tapprox. 49-53 MGOe11 kOe or moreapprox. 60-80°C
N42SHapprox. 1.28-1.32 Tapprox. 40-42 MGOe20 kOe or moreapprox. 150°C
N38UHapprox. 1.22-1.25 Tapprox. 36-38 MGOe25 kOe or moreapprox. 180°C
Ferrite (reference)approx. 0.38-0.42 Tapprox. 3.5-4.5 MGOe-approx. 250°C

Coatings, shipping and safety rules have approximate criteria too.

A Caution on Using These Figures The figures above are approximate values condensed for practical use from public standards and industry catalogs as of November 2026. Br and Hcj ranges by grade differ slightly between factories and standards, and maximum working temperature changes greatly with magnet shape. Toy magnet rules and air shipping rules have different details by sales market and airline, so confirm the exact criteria with the certification body, test lab and forwarder before testing and shipping.

6. Gaps in Magnet Test Reports

When you ask a factory for proof, it usually sends a grade report from the magnet material supplier or its own measurement sheet. The documents themselves are rarely fake. The link between what the document covers and the product being made right now is simply broken.

GapWhat It Looks LikeWhat to Check
Gauss measurement sheetNumbers only, without measuring position, probe height or magnet sizeMeasuring conditions, comparison with the approved sample under the same conditions
Block material reportBH values of a large block before cutting; unclear if it is your lotLot number, link between the cutting and plating factory and the block source
Missing temperature gradeOnly "N52," no Hcj value or H/SH markingMeasured Hcj, high-temperature demagnetization results
Plating reportRepresentative specimen results from the plating plant, layers and thickness unclearLayer structure and thickness, salt spray on your own magnets
Toy test scopeOnly the magnet tested; no check whether it comes loose after drop and tension testsFlux index and detachment after use and abuse tests on the finished product
Magnetic test report for shippingMeasured with different packaging or quantityA report measured on the actual shipping package
Outdated reportResults from one or two years ago; the material supplier or alloy has changed sinceIssue date and history of material supplier changes
Get Photos of the Blocks and the Plating Line Small magnets are usually made by a cutting plant slicing large blocks from a material supplier and sending them to a plating plant. Photos of the block label with grade and lot number, the cutting site and the plating line's layer structure sheet show whether the report connects to your goods. For delivered magnets, simply weighing them to check that weight per piece matches the sample filters out downsizing and material substitution.

7. Common Supplier Substitutions

Neodymium magnet prices are tightly tied to rare earth prices, so dropping the grade a step or two, or swapping a high-temperature grade for a standard one, cuts cost immediately. Sticking the magnet on by hand will not reveal the difference. Here are the types we have actually encountered in consultations.

TypeMethodHow to Prevent It
N52 in samples onlySamples are N52, mass production ships N35 to N42BH measurement and pull force baseline on the approved sample, remeasure production goods
Dropping the temperature gradeOrdered N42SH, delivered N42Measured Hcj, high-temperature demagnetization test
Thinner platingSingle nickel layer instead of three-layer Ni-Cu-Ni, reduced thicknessCoating thickness measurement, salt spray test
Smaller magnets2.0mm thickness becomes 1.8mm, diameter cut by 0.2mmStated dimensional tolerances, weight per piece check
Material swapBonded instead of sintered, ferrite in some positionsDensity measurement, strength baseline comparison
Wrong magnetization direction or polarityDiametric instead of axial magnetization, polarity flipped in assemblyPolarity rules, 100% or sample check with a polarity tester
Skipping adhesive or retentionLess adhesive or fewer ribs holding magnets in toys and casesMagnet detachment test after drop and tension

The most common in practice is making samples in a higher grade and dropping a step or two in mass production. Hands cannot tell, and surface gauss can be made to look similar just by moving the measuring point, so without a pull force baseline and an Hcj condition in the spec sheet, there is nothing to hold the factory to. The process for requiring prior approval of process changes was covered in Episode 119.


8. The Damage When Magnet Quality Slips

Magnet problems surface all at once, not right after sale but after a season changes or an accident happens, and they affect the whole lot.

See Episode 53 for recalls and product liability and Episode 49 for dangerous goods shipping. High-temperature grades containing dysprosium or terbium can be affected by China's export controls on heavy rare earths, so confirm with the factory before ordering whether an export license is required. Export controls in general were covered in Episode 120.


9. Items to Put in the Spec Sheet

Every factory reads "强磁" differently. Organize the items below into a table and attach it to the spec sheet.

ItemExample
Material and gradeSintered NdFeB, N42 or higher (Br and (BH)max ranges per GB/T 13560)
Temperature gradeSH or higher (Hcj 20 kOe or more), maximum use temperature ○°C
Dimensions and toleranceΦ20 × 2.0mm, tolerance ±0.05mm, weight per piece ○g ±○%
Magnetization direction and polarityAxial (through thickness), outer face N pole after assembly, how polarity is marked
CoatingNi-Cu-Ni, total thickness ○μm or more, no rust after ○ hours neutral salt spray
Finished-product strengthPull force ○N or more based on the approved sample (plate thickness and conditions stated), within -10% of the sample
Heat resistanceRoom-temperature pull force loss within ○% after ○ hours at ○°C
Safety conditionsFor children's products, pass the sales market's toy flux index and detachment tests, with warnings
ShippingMagnetic test report on the actual package for air shipments, shielded packing if needed
Change controlPrior written approval for changes to material supplier, grade, plating plant or dimensions

The most effective lines are the finished-product pull force baseline and the temperature grade. With those two, goods with a lowered grade fail the pull force check, and goods switched to a standard grade fail the high-temperature test. See Episode 59 for writing spec sheets and BOMs.


10. Adding Magnet Checks to Your QC Checklist

Sample Stage

The sample stage sets the baseline. Measure the BH curve of the approved sample magnets to confirm the grade and temperature grade, and measure pull force and surface field on the finished product under set conditions. For car or in-device use, run the high-temperature demagnetization test at this stage; for humid environments, the salt spray test. Do not record only "pass"; record the actual numbers. That is how you can compare how far mass production has fallen from the baseline. Sample management was covered in Episode 34.

Production Stage

On the days blocks arrive and cutting and plating run, get photos or video of the block label with grade and lot number, and of the plating line's layer structure sheet. On the line where magnets go into the finished product, check how polarity is verified and how the magnets are glued or retained. See Episode 102 for production tracking.

Pre-Shipment Inspection Stage

The inspector picks samples directly from packed finished goods and measures pull force and surface field under the same conditions as the baseline. For loose magnets, check weight, dimensions and coating thickness too, and verify polarity with a polarity tester. Seal some samples and send them to a lab for BH curve or high-temperature testing. Do not use "attach a phone and shake it" as a basis for judgment. Pre-shipment inspection is covered in Episode 100.

Sample Magnet Control Conditions for a Magnetic Car Phone Mount Magnets shall be sintered NdFeB grade N48SH or higher (Hcj 20 kOe or more) and meet the spec sheet dimensions of Φ20 × 2.0mm (±0.05mm), axial magnetization and outer face N pole. Coating shall be Ni-Cu-Ni with a total of 15μm or more, with no rust after 48 hours of neutral salt spray. Finished products shall reach at least 90% of the approved sample's pull force, and room-temperature pull force loss after 4 hours at 85°C shall be within 5%. Changes to grade, material supplier, plating conditions or dimensions require prior written approval. Before shipment, randomly selected samples undergo pull force and high-temperature tests. If the criteria are not met, the entire lot is remade or returned, with testing and logistics costs borne by the supplier.

11. Sample Request Wording to Send the Factory

Putting the following wording in your purchase order or spec sheet takes magnet grade and coating out of the factory's discretion and makes it easier to assign responsibility when problems arise.

"本产品磁铁须使用烧结钕铁硼,牌号不低于N48SH(Hcj≥20kOe),尺寸Φ20×2.0mm(公差±0.05mm),厚度方向充磁,装配后外侧为N极。镀层为镍铜镍,总厚度不低于15μm,中性盐雾48小时不得生锈。成品吸力不得低于确认样品吸力的90%(按规格书注明的铁板及测试条件),85℃放置4小时后常温吸力衰减不超过5%。表面高斯值报告不能代替上述测试。如需更改牌号、磁材供应商、镀层工艺或尺寸,须提前书面确认。生产时请提供毛坯标签(牌号、批号)及电镀工艺的照片。空运出货须提供按实际包装检测的磁检报告。出货前由我方从成品中随机抽样检测吸力并送第三方检测,如不合格,整批重做或退货,检测及物流费用由供应商承担。"

(The magnets in this product must be sintered NdFeB, grade N48SH or higher (Hcj≥20kOe), Φ20×2.0mm (tolerance ±0.05mm), magnetized through the thickness, with the N pole facing out after assembly. Coating is Ni-Cu-Ni, total thickness at least 15μm, with no rust after 48 hours of neutral salt spray. Finished-product pull force must be at least 90% of the approved sample (using the steel plate and test conditions in the spec sheet), and room-temperature pull force loss after 4 hours at 85°C must not exceed 5%. Surface gauss reports cannot replace these tests. Any change to grade, magnet material supplier, plating process or dimensions requires prior written confirmation. During production, please provide photos of the block labels (grade, lot number) and the plating process. Air shipments require a magnetic test report measured on the actual packaging. Before shipment, we will randomly sample finished goods to measure pull force and send them to a third-party lab. If they fail, the entire lot will be remade or returned, with testing and logistics costs borne by the supplier.)


12. Three Real Cases

These are anonymized versions of types we encounter often in consultations. Amounts and figures are examples.

Case 1 - Car Mounts That Weakened Over the Summer

This is the case from the opening. The purchase order had a single line, "N52, 镀镍 (nickel plated)," with no temperature grade, no finished-product pull force, and no plating layers or thickness. The factory held firm that "the gauss sheet shows over 3,000, so we did our part," and since the sheet had no measuring conditions, there was little ground to argue. In the end the company spent a whole season handling reviews and exchanges, and sold the remaining stock at a discount as indoor mounts. Its spec sheet now includes an SH grade, a high-temperature test and a finished-product pull force baseline.

Case 2 - Magnetic Blocks That Lost Their Magnets in a Drop Test

A seller making children's magnetic building blocks in Chenghai (澄海), Shantou, Guangdong, for Korean online marketplaces got inquiries right after launch saying "a block corner cracked and a magnet rolled out." The test results the factory had sent only measured the flux index of the loose magnet; nobody had checked whether magnets came loose after the blocks were dropped and pulled. It later turned out that during production the factory had thinned the block walls and cut back the adhesive holding the magnets to save cost. The escaped magnets fit in the small parts cylinder and had a flux index well above 50. The seller stopped sales and recalled every unit.

Case 3 - Magnetic Phone Cases Stopped at Express Air Freight

A company that made 20,000 wireless-charging-compatible magnetic phone cases in Shenzhen (深圳), Guangdong, booked express air freight to meet a crowdfunding delivery schedule. Right before departure, the forwarder asked for a magnetic test report, but the one the factory had was measured on different packaging. Measured on the actual packaging, the shipment exceeded the limit, and repacking with shielding cost three days. While repacking, they also found that in some lots the magnet rings had been assembled with the polarity flipped. Had polarity not been added to the pre-shipment inspection items, those cases would have gone straight to backers.


13. Common Mistakes

The most common is ending the check by sticking the magnet on by hand. Even low grades of neodymium are strong enough that touch will not catch a lowered grade. We also often see buyers accepting gauss values without measuring conditions as grade proof, writing only "N52" and leaving out the temperature grade, and checking only new magnets at room temperature without heat or humidity conditions. Many also test only the loose magnet without checking whether it comes out of the finished product, yet safety problems usually start not with the magnet but with the structure holding it.


14. Magnet Quality Control Checklist

Sample Stage

Production Stage

Pre-Shipment Inspection Stage


Final Thoughts - Not How Hard It Sticks, but What Holds Up and for How Long

Magnets leaving the factory, whether N35 or N52, standard or high-temperature grade, all shine the same silver and snap onto steel just as hard. The difference shows up in a hot car in summer, in bathroom humidity, or after a block breaks in a child's hand. Writing grade, temperature grade, coating and a finished-product pull force baseline into the spec sheet, and measuring samples pulled from mass production, costs far less than a season of exchanges or a recall.

There is something you can do right now. Ask the factory currently producing for you for the exact grade and temperature grade of the magnets in use, the measured Hcj, and the coating layer structure. If the only answer is "放心,高斯够 (Don't worry, the gauss is enough)," draw up a magnet control sheet and send it before your next order.

StartMade supports you from choosing the right grade and temperature grade and writing the spec sheet, through reviewing supplier reports and checking block and plating sites during production, to pre-shipment inspection including pull force, high-temperature and salt spray testing, and magnetic testing for air shipping. If you have already had a magnet problem, we can start by measuring remaining stock; if you are preparing a new product, we can start together with grade selection and the spec sheet.

Are the Magnets in Your Product Really N52?

From choosing grade and temperature grade to report review, pull force and high-temperature tests and pre-shipment inspection
We check before summer complaints and sales reviews

Phone   010-9980-9959
Email   deanpark@greenfrogseoul.com
KakaoTalk   pf.kakao.com/_NzSNX
Website   www.startmade.co.kr

Frequently Asked Questions

What is the difference between N52 and N35 magnets?
The number after N is the maximum energy product in MGOe, so at the same size an N52 magnet is roughly 20 to 30 percent stronger than an N35. N52 is relatively weak against heat, though, so in hot places like a car interior the temperature grade, such as SH, can matter more than the number. The actual grade is confirmed by a lab BH curve measurement, not by feel or surface gauss.
Do neodymium magnets lose strength when heated?
Yes. Strength drops temporarily as temperature rises, and once a magnet passes the limit temperature of its grade, part of the strength does not return after cooling. The standard N grade is generally rated to about 80°C and the SH grade to around 150°C. For car or in-device use, write the temperature grade into the spec sheet and get high-temperature test results.
Can products with magnets be shipped by air?
Yes, but under IATA PI 953 a package is treated as dangerous goods if the magnetic field 2.1m from its surface exceeds 0.159 A/m. Before air shipping you need a magnetic test report measured on the actual packaging, and shielded packing if the limit is exceeded. Sea freight is usually not subject to this restriction, but confirm with your forwarder in advance.