StartMade Blog Episode 170 ·

The "12-Hour" Insulated Tumbler Was Lukewarm by Lunchtime

Vacuum Insulation, Stainless Steel and Lead Sealing Point Testing Guide for Vacuum Flasks, Tumblers and Insulated Food Jars

Hello, this is StartMade.

A home goods brand imported 30,000 500ml vacuum tumblers from a vacuum flask factory in Yongkang (永康), Zhejiang. The purchase order said "304不锈钢真空保温杯, 保温12小时 (304 stainless steel vacuum cup, keeps hot 12 hours)," and the factory sent its own measurement sheet stating "保温效能合格 (insulation performance passed)." Coffee poured into the sample in the morning was still warm in the evening, and inspection passed everything: appearance, capacity, even lid leakage.

From the second month of sales, the reviews changed. Comments like "water I fill in the morning is lukewarm by lunch" and "pour in hot water and the outside gets hot too" kept piling up. Randomly picking returned units and warehouse stock and measuring them showed that one or two in ten had lost their vacuum, and some had also skipped the copper plating that acts as a reflective layer between the inner and outer walls. The factory contact answered: "抽完真空当天就测了,都是好的 (We tested them all on the day we pulled the vacuum, and they were all fine)."

Vacuum is invisible, and most units measure fine on the day the vacuum is pulled. A unit whose seal leaks very slightly loses its vacuum gradually over days or weeks, so an inspection on the day of shipment cannot catch it. Processes that use lead-containing material at the bottom sealing point are also still common, and the moment the bottom cap falls off, the problem changes from insulation performance to safety. This post covers how vacuum flasks are made, standards that differ by product and market, checking methods and their limits, approximate criteria, gaps in test reports, common supplier substitutions, and what to cover in the spec sheet and at inspection.

Words like "304", "保温12小时 (keeps hot 12 hours)" or "真空 (vacuum)" guarantee nothing on their own. Write the steel grade and thickness of the inner and outer walls, the vacuum sealing method and whether it is lead-free, the use of copper plating and getters, hot and cold retention test conditions and reference temperatures, the holding period after evacuation and 100% temperature checks, and food contact testing into the spec sheet, then measure samples pulled from mass production. That is what keeps you from insulation complaints and safety problems.

Note This post is based on common practices of stainless steel vacuum flask and tumbler factories in Yongkang (永康), Wuyi (武义) and Jinhua (金华) in Zhejiang, and Chaozhou (潮州) and Jieyang (揭阳) in Guangdong as of November 2026, widely used industry criteria, and public standards such as China's GB/T 29606 (stainless steel vacuum cups), GB 4806.9 (metal materials for food contact), EN 12546-1 (vacuum vessels for household use) and Japan's vacuum flask labeling under the Household Goods Quality Labeling Act. The figures in this post are approximate values used in practice. Food contact standards and labeling rules differ by product and sales country and change often, so always confirm the requirements that apply with the certification body and test lab.

1. Every Unit Is Fine on Evacuation Day - Why Vacuum Defects Slip Through Inspection

A vacuum flask is made by nesting two stainless steel cups, welding them together at the mouth, and pumping the air out from between the two walls so heat cannot cross. Its performance depends almost entirely on the vacuum in that gap. But the vacuum cannot be seen from outside, and a unit that has lost its vacuum is identical to a good one in shape, weight and lid assembly.

Trickier still are defects where the vacuum leaks out slowly. A tiny pinhole in a weld or a poor seal shows nothing for a day or two, then air seeps in bit by bit over several weeks and insulation drops. Chinese factories call this "慢漏 (slow leak)." A factory that does it properly holds units for a set period after evacuation and then checks the temperature of every unit again, but when the deadline is tight, this holding period is the first thing the factory cuts. Then a batch that passed in full on evacuation day starts failing one unit at a time after it reaches customers.

The common inspection check of "pour in hot water and touch the outside" also has clear limits. Units that have lost all their vacuum are caught immediately, but units that have lost only part of it are hard to tell apart by hand. Verifying stainless steel grades was covered in Episode 150; this post focuses on vacuum insulation performance, sealing point safety and the material issues specific to vacuum flasks.


2. How a Vacuum Flask Is Made

Knowing the structure shows you where cost gets cut. Process names vary a little from factory to factory, but the order is nearly the same.

Process / PartChinese Factory TermRoleWhere Cost Gets Cut
Inner and outer walls内胆, 外壳Inner cup the drink touches and outer cup, usually 304 or 316Outer or inner wall switched to 201, thinner sheet
Mouth welding口部焊接, 激光焊Joins and seals the mouths of the two cupsFaster welding speed, more pinholes
Copper plating / reflective layer镀铜, 包铜箔Applied to the outer face of the inner wall to cut radiant heatPlating skipped or coverage reduced
Getter吸气剂Absorbs gas left in the vacuum gap to keep the vacuum longerSkipped
Evacuation and sealing抽真空, 封口(钎焊/玻璃珠/无尾)Air pumped out through a hole in the bottom, then closed with sealing materialLead-containing sealing material, shorter evacuation time
Holding and re-checking temperature静置, 复测温Filters out slow-leak unitsHolding period shortened or skipped
Exterior coating and printing喷粉, 喷漆, 印刷Color and logoPretreatment skipped, thinner coating
Lid and gasket杯盖, 硅胶圈Sealing and leak preventionSwitched to cheap plastic, recycled silicone or TPE

There are three main sealing methods. One places solder sealing material on the bottom hole and melts it in a vacuum furnace to close it; another melts a glass bead to close it; and the "无尾真空 (tailless vacuum)" method has no hole at all and seals the weld itself inside the vacuum furnace. The first two require checking what the sealing material contains, and solder sealing materials in particular have long been commonly made with lead. The sealing point is usually hidden under a bottom cap or sticker and cannot be seen in use, but it is fully exposed once the cap comes off.


3. Standards That Differ by Product and Market

A vacuum flask is a food contact article that drinks touch, and also a product sold on its advertised insulation time. So the standards split two ways: food contact safety and performance claims.

CategoryKoreaUSEU / UKJapan / China
Food contact (metal)Food Sanitation Act standards for utensils, containers and packaging, migration limits for metalsFDA food contact substance regulationsRegulation (EC) 1935/2004, member state rules and guidelines for metalsJapan Food Sanitation Act, China GB 4806.9
Lids and gaskets (plastic, silicone)Standards for utensils, containers and packaging, migration by materialRelevant FDA 21 CFR sectionsRegulation (EU) 10/2011, member state rules for siliconeChina GB 4806.7, GB 4806.11
Insulation performanceLabeling and advertising liability (supporting data required)Advertising substantiationEN 12546-1 test method as referenceMandatory heat retention labeling in Japan, China GB/T 29606
Lead and other hazardous substancesHazardous substance limits in children's product safety standards for children's itemsCalifornia Prop 65 warnings, CPSIA lead limits for children's itemsREACH lead restrictionCriteria by product

"Keeps hot 12 hours" on a sales page is an advertising claim, so if a complaint or dispute arises, you have to produce the test data behind it. If you sell in Japan, the Household Goods Quality Labeling Act requires labeling heat retention as a minimum temperature after a set number of hours, so it is better to align test conditions with the Japanese standard from the start. For products children use, such as kids' straw tumblers, lead at the bottom sealing point leads straight to a hazardous substance limit problem. See Episode 64 for importing food contact products, Episode 65 for children's products and Episode 165 for hazardous substance testing.


4. Checking Methods - From Touching the Outside to Re-Checking After Holding

Ask "保温多久? (How long does it keep hot?)" and the factory almost always answers "12小时没问题 (12 hours, no problem)." The only way to verify that is to set conditions and measure it yourself, and each method shows a different range of things.

MethodHow It WorksWhat It ShowsLimits
Touching the outsideFill with boiling water and touch the outer wall a few minutes laterUnits that have lost all vacuumHard to tell units that have lost only part of it
Infrared outer wall measurementFill with hot water and measure outer wall temperature with a non-contact thermometer after a set timeFast 100% screeningMeasuring time and room temperature must be fixed; misses slow leaks
Hot and cold retention testFill with water at 95°C or above, or 4°C or below, and measure water temperature after 6 and 12 hoursActual insulation performance, advertising substantiationTakes a long time; water volume, room temperature and lid conditions must be set
Re-checking after holdingHold for a set period after evacuation, then measure againSlow-leak unitsSchedule grows by the holding period
Lid leak testFill with water and stand upside down or shakeGasket and thread leaksLeaks caused by temperature change need a separate check
XRF and composition analysisX-ray check of inner and outer wall steel grades and sealing point composition201 mixed in, lead in the sealing materialCap must be removed to measure the sealing point
Food contact migration testLab migration analysis against the sales country's standardCompliance of metal, plastic and silicone migrationWhether the tested sample matches mass production must be checked separately

A Retention Test Only Becomes a Number When You State the Conditions

A value like "70°C after 6 hours" can easily shift by 5°C or more depending on the water temperature, how full it was, the room temperature and whether it was preheated. Fill to the brim after preheating with boiling water and the number comes out good; fill only to rated capacity without preheating and it comes out low. The spec sheet should state the conditions too, such as "room temperature 20±2°C, preheated, filled to rated capacity with water at 95°C or above, lid closed and standing upright, at least ○°C after 6 hours," so that mass production can be compared.

Slow Leaks Only Show If You Wait

Many factories check the temperature of every unit on evacuation day, but that check alone does not catch slow leaks. You need to confirm whether there is a procedure to hold units for a set period and then check every unit again, and whether that period was actually kept. The holding period varies by factory but is usually from a few days to one or two weeks. If this period is not built into the order schedule from the start, a factory chasing the deadline skips this step first.

You Only Know the Sealing Point by Opening the Cap

Whether the bottom sealing point contains lead cannot be told from the outside of a finished unit. At the sample stage, remove the bottom cap or sticker and measure the sealing point with XRF, or ask the factory for documentation of the sealing method and sealing material composition. If you settled on lead-free sealing material or the tailless vacuum method, open a few units before shipment to confirm mass production uses the same method.


5. Approximate Criteria

Below is a summary of values commonly seen in the industry. Insulation performance varies greatly with capacity, mouth diameter and lid structure, so before sending anything for testing, decide which standard and conditions you will judge against.

ItemCommonly Seen Range (reference)Notes
Heat retention (narrow-mouth flask, around 500ml)Approx. 70-80°C after 6 hours from 95°C waterNarrower mouth and thicker stopper help
Heat retention (wide-mouth tumbler, around 500ml)Approx. 60-70°C after 6 hours from 95°C waterLower with slide or straw lids
Cold retentionApprox. 8-12°C or below after 6 hours from 4°C waterState whether ice is included in the conditions
Outer wall temperatureNearly the same as room temperature a few minutes after filling with hot waterA warm outer wall suggests a vacuum defect
Sheet thicknessApprox. 0.3-0.5mm for inner and outer wallsCheck indirectly by weight per unit
Capacity toleranceRoughly ±5% of labeled capacityState whether it is "brim-full capacity" or "rated capacity"

Materials have approximate criteria too.

A Caution on Using These Figures The figures above are approximate values condensed for practical use from public standards and industry data as of November 2026. Insulation performance varies greatly with capacity, mouth diameter, lid structure and test conditions, and food contact standards and hazardous substance limits differ by sales country and user age. Confirm the actual judging criteria with the certification body and test lab before testing.

6. Gaps in Vacuum Flask Test Reports

When you ask a factory for proof, it usually sends its own insulation measurement sheet and a food contact test report. The documents themselves are rarely fake. The link between what the document covers and the product being made right now is simply broken.

GapWhat It Looks LikeWhat to Check
In-house insulation sheetOnly "合格 (pass)" written, no water temperature, room temperature or preheating conditionsTest conditions, values from the approved sample under the same conditions
Evacuation-day temperature recordsNo records of re-checking after holdingHolding period, re-check dates and defect rates
Report for a different modelTested on another capacity or lid from the same factoryModel name and photos of the tested sample
Raw sheet reportStainless steel coil report; unclear if it covers your inner and outer wallsLink between coil number and production lot, XRF on finished goods
Food contact report scopeOnly the body tested; lid, gasket and straw left outWhether every part the drink touches was tested
Hazardous substance report scopeOnly the exterior coating tested; bottom sealing point left outWhether the sealing point composition was tested
Outdated reportResults from one or two years ago; the sealing material or paint supplier has changed sinceIssue date and history of supplier changes
Get Photos of the Holding Area and the Temperature Records A factory that does it properly has a separate holding area where evacuated units are stacked by date, and it writes the number of defects in its re-check records. Getting photos of this area and the dated re-check records during production shows right away whether the holding period was kept. For delivered goods, simply weighing them to check that weight per unit matches the sample filters out thinner sheet.

7. Common Supplier Substitutions

Vacuum flask prices are tightly tied to stainless steel weight and process time, so thinner sheet or a shorter holding period cuts cost and lead time immediately. The difference barely shows while the product is new. Here are the types we have actually encountered in consultations.

TypeMethodHow to Prevent It
Skipping the re-check after holdingOnly an evacuation-day temperature check, then straight to packingStated holding period, dated re-check records required
Skipping copper plating or gettersCopper plating and getters in samples only, left out in mass productionPhotos at the semi-finished stage, repeat retention test
Steel grade swapOuter or inner wall changed from 304 to 201XRF on finished goods, steel grade stamped on the inner wall
Thinner sheet0.4mm becomes 0.3mmStated weight-per-unit tolerance
Lead sealing materialLead-free in samples, the old solder sealing material in mass productionStated sealing method, XRF on production sealing points
Gasket and lid material swapFood-grade silicone replaced with cheap silicone or TPE, lid resin changedMaterial stated for each part, odor and migration tests
Skipping coating pretreatmentSandblasting and degreasing skipped, thinner coatingCross-cut and repeated washing tests

The most common in practice is skipping the re-check after holding. Factories usually skip it because they are chasing a deadline, not to hide defects, but the units fail in customers' hands either way. If the spec sheet does not require a holding period and submission of re-check records, there is nothing to hold the factory to. The process for requiring prior approval of process changes was covered in Episode 119. See Episode 154 for silicone gasket materials and Episode 130 for exterior coating adhesion.


8. The Damage When Vacuum Flask Quality Slips

Vacuum flask problems surface not right after sale but weeks or months later, and they often spread across the whole lot.

See Episode 53 for recalls and product liability. Resistance to salt can also be compared with the test covered in Episode 128.


9. Items to Put in the Spec Sheet

Every factory reads a single line of "304真空保温杯 (304 vacuum insulated cup)" differently. Organize the items below into a table and attach it to the spec sheet.

ItemExample
Steel grade and thicknessInner wall SUS304 (or 316), outer wall SUS304, sheet thickness ○mm, weight per unit ○g ±○%
Vacuum structureCopper plating on the inner wall, getter used, sealing method (lead-free sealing material or tailless vacuum)
Holding and re-checkHeld at least ○ days after evacuation, then 100% temperature re-check, dated records submitted
Heat retentionRoom temperature 20±2°C, preheated, water at 95°C or above to rated capacity, at least ○°C after 6 hours
Cold retentionWater at 4°C or below, ○°C or below after 6 hours (state whether ice is included)
CapacityRated capacity ○ml, tolerance ±○%, measuring basis (brim-full or rated line) stated
Lid and gasketLid resin type, food-grade silicone gasket, no leaks after ○ hours upside down
Exterior finishCoating type, cross-cut criteria, repeated washing test if labeled dishwasher safe
Food contact and hazardous substancesMigration tests to the sales country's standard (body, lid and gasket all included), lead test on the sealing point
Change controlPrior written approval for changes to steel grade, sheet thickness, sealing method, paint or gasket material

The most effective lines are the re-check after holding and the retention test conditions. With those two, rushed-to-pack goods show up in the records, and goods missing copper plating or getters fail the repeat retention test. See Episode 59 for writing spec sheets and BOMs.


10. Adding Vacuum Flask Checks to Your QC Checklist

Sample Stage

The sample stage sets the baseline. Run hot and cold retention tests on the approved sample under set conditions, measure the inner and outer walls with XRF, and open the bottom cap to confirm the sealing method and sealing point composition. Record weight per unit and capacity at this stage too. Do not record only "pass"; record the actual numbers. That is how you can compare how far mass production has fallen from the baseline. Sample management was covered in Episode 34.

Production Stage

Get photos or video of the semi-finished stage where copper plating and getters go in, the stage where sealing material is placed before units enter the vacuum furnace, and the post-evacuation holding area. A sudden rise in the defect rate in the dated re-check records is a sign that something changed in the welding or vacuum process. See Episode 102 for production tracking.

Pre-Shipment Inspection Stage

The inspector picks samples directly from packed finished goods and measures outer wall temperature, and runs a 6-hour retention test on some of them under the same conditions as the baseline. Check weight per unit, capacity, lid leakage and coating cross-cut at the same time, and open the bottom cap on a few units to confirm the sealing method matches the sample. Seal some samples and send them to a lab for composition and migration testing. Do not pass goods based only on touching the outside. Pre-shipment inspection is covered in Episode 100.

Sample Control Conditions for a 500ml Vacuum Tumbler Inner and outer walls shall be SUS304 with a sheet thickness of 0.4mm or more, and weight per unit shall be within ±3% of the approved sample. Copper plating and a getter shall be applied to the inner wall, and sealing shall use lead-free sealing material or the tailless vacuum method. After evacuation, units shall be held for at least 7 days, then 100% re-checked for temperature, with dated records submitted. At room temperature of 20±2°C, after preheating and filling to rated capacity with water at 95°C or above, the temperature after 6 hours shall be 65°C or above. Changes to steel grade, sheet thickness, sealing method, paint or gasket material require prior written approval. Before shipment, randomly selected samples undergo retention tests and sealing point checks. If the criteria are not met, the entire lot is remade or returned, with testing and logistics costs borne by the supplier.

11. Sample Request Wording to Send the Factory

Putting the following wording in your purchase order or spec sheet takes the vacuum process and materials out of the factory's discretion and makes it easier to assign responsibility when problems arise.

"本产品内胆及外壳均须使用SUS304不锈钢,板厚不低于0.4mm,单只重量与确认样品相差不超过±3%。内胆须镀铜并使用吸气剂,封口须采用无铅钎料或无尾真空工艺,不得使用含铅封口料。抽真空后须静置不少于7天再全检测温,并按日期提供复测记录。保温效能按以下条件测试:室温20±2℃,预热后注入不低于95℃的热水至额定容量,盖紧直立放置6小时后水温不低于65℃。工厂自测“合格”记录不能代替上述测试。如需更改材质、板厚、封口工艺、涂料或硅胶圈材质,须提前书面确认。生产时请提供镀铜、封口工序及静置区的照片。出货前由我方从成品中随机抽样测试保温效能、拆底检查封口并送第三方检测,如不合格,整批重做或退货,检测及物流费用由供应商承担。"

(The inner and outer walls of this product must both be SUS304 stainless steel, sheet thickness at least 0.4mm, with weight per unit within ±3% of the approved sample. The inner wall must be copper plated with a getter, and sealing must use lead-free solder or the tailless vacuum process; lead-containing sealing material must not be used. After evacuation, units must be held for at least 7 days before a 100% temperature check, with re-check records provided by date. Heat retention is tested under the following conditions: room temperature 20±2°C, preheated, filled to rated capacity with hot water of at least 95°C, lid closed tightly and standing upright, with water temperature of at least 65°C after 6 hours. The factory's in-house "pass" records cannot replace these tests. Any change to material, sheet thickness, sealing process, paint or silicone gasket material requires prior written confirmation. During production, please provide photos of the copper plating and sealing processes and the holding area. Before shipment, we will randomly sample finished goods to test heat retention, open the bottom to inspect the seal, and send them to a third-party lab. If they fail, the entire lot will be remade or returned, with testing and logistics costs borne by the supplier.)


12. Three Real Cases

These are anonymized versions of types we encounter often in consultations. Amounts and figures are examples.

Case 1 - Tumblers That Went Lukewarm After Two Months

This is the case from the opening. The purchase order had a single line, "304, 保温12小时 (keeps hot 12 hours)," with no retention test conditions, no re-check after holding, and nothing about copper plating. The factory held firm that "we checked every unit's temperature on evacuation day, so we did our part," and since the measurement sheet had no conditions, there was little ground to argue. It turned out the factory had packed units right away with no holding period to meet the deadline, and later lots were missing copper plating as well. The company spent a whole season handling exchanges and reviews, and its spec sheet now includes a 7-day holding period with a re-check and retention test conditions.

Case 2 - A Kids' Straw Tumbler That Lost Its Bottom Cap

A seller making kids' straw tumblers in Chaozhou (潮州), Guangdong, for Korean online marketplaces got an inquiry saying "the bottom cap came off and there's a silver dot inside." Measuring the sealing points of the remaining stock with XRF showed high lead. The hazardous substance report received at the sample stage had only tested the exterior coating and the silicone straw; the sealing point was outside the test scope. The adhesive holding the bottom cap had also been switched to a cheaper one during production. The seller stopped sales and recalled every unit.

Case 3 - Inner Walls That Rusted from Sports Drinks

A company that made 1-liter large-capacity bottles in Wuyi (武义), Zhejiang, got reviews from gym members saying "I kept a sports drink in it and brown spots appeared inside." The sample inner wall was 304, but measuring production inner walls with XRF showed some lots were 201, with less nickel and more manganese. Weight per unit was also lighter than the sample, revealing that the factory had thinned the sheet as well. Had XRF and weight checks been part of the pre-shipment inspection, the problem would have been caught before loading.


13. Common Mistakes

The most common is ending the check after pouring in hot water and touching the outside. That only catches units that have lost all their vacuum, so units that have lost part of it, or will lose it later, ship as they are. We also often see buyers accepting a "保温合格 (insulation passed)" sheet without conditions as proof, leaving the post-evacuation holding period out of the schedule, and running food contact tests only on the body while leaving out the lid, gasket and sealing point. The insulation time you advertise should be set from test results under defined conditions, not the factory's in-house results, if you want to avoid trouble later.


14. Vacuum Flask Quality Control Checklist

Sample Stage

Production Stage

Pre-Shipment Inspection Stage


Final Thoughts - Not Whether It Is Warm Today, but Whether It Is Still Warm in Two Months

Vacuum flasks leaving the factory, whether the vacuum is properly set or slowly leaking, whether 304 or 201, all shine the same and feel equally solid. The difference shows up weeks later, when a customer's morning coffee has gone cold by lunch, or when a bottom cap pops off a tumbler a child dropped. Writing the re-check after holding, retention test conditions, sealing method and steel grade into the spec sheet, and measuring samples pulled from mass production, costs far less than a season of exchanges or a recall.

There is something you can do right now. Ask the factory currently producing for you how many days units are held after evacuation, whether there are re-check records, and whether the sealing material contains lead. If the only answer is "放心,我们都测过 (Don't worry, we've tested them all)," draw up a vacuum flask control sheet and send it before your next order.

StartMade supports you from choosing the right steel grade and structure for the use and writing the spec sheet, through reviewing supplier reports and checking the vacuum and sealing processes and holding area during production, to pre-shipment inspection including retention tests and sealing point checks, and arranging food contact testing. If you have already had an insulation problem, we can start by measuring remaining stock; if you are preparing a new product, we can start together with structure selection and the spec sheet.

Will Your Vacuum Flasks Still Keep Hot in Two Months?

From choosing steel grade and structure to report review, retention tests, sealing point checks and pre-shipment inspection
We check before insulation complaints and recalls

Phone   010-9980-9959
Email   deanpark@greenfrogseoul.com
KakaoTalk   pf.kakao.com/_NzSNX
Website   www.startmade.co.kr

Frequently Asked Questions

How is the heat retention of a vacuum flask tested?
At a room temperature of about 20°C, preheat the flask with boiling water, fill it to rated capacity with water of 95°C or higher, close the lid and measure the water temperature after 6 or 12 hours. Fill level, room temperature and preheating can shift the result by more than 5°C, so the conditions must be fixed before products can be compared. Use the test conditions in China's GB/T 29606 or EN 12546-1 as a reference and write them into the spec sheet.
Is there lead in the bottom seal of vacuum flasks?
Some factories still use leaded solder to seal the evacuation hole in the bottom. The seal sits under the bottom cap, so it normally never touches drinks or hands, but it is fully exposed if the cap falls off. For children's products or strict markets, specify lead-free sealing material or a tailless vacuum process and check production seals with XRF.
Why does the outside of my tumbler get hot?
If the outer wall warms up within a few minutes of adding hot water, the vacuum between the two walls has most likely been lost. Air gets in through tiny pinholes in the weld or a faulty seal, and heat then passes straight to the outer wall. A lost vacuum cannot be restored, so the unit needs replacing, and if several units from one lot fail, ask the factory for its post-storage retest records first.